Extron MTP 15HD RS 系列是多用途微型双绞线发送器和接收器系列，可通过单根非屏蔽双绞线电缆长距离传输 VGA 和 RS-232 串行控制信号至演示显示设备。它们兼容高达 1920 x 1200 (WUXGA) 的分辨率，支持的 VGA 信号电缆传输距离可达 185 m (600') 或更远，UXGA 信号可达 135 m (450') 或更远。
在那些需要将高分辨率视频信号长距离传输至管道空间有限的显示设备的系统中，或者布线会暴露及可见的系统中，MTP 15HD RS系列是理想之选。理想的应用场所包括机场的公共信息显示处、博物馆、电影院和旅馆。
| 快速参考 |
|---|
| Everlast 电源 (宣传册) |
| MTP 15HD RS 系列 (宣传册) |
| 相兼容的切换器和矩阵切换器 | ||
|---|---|---|
| MTP SW6 | 6 路输入 MTP 双绞线切换器 | |
| 相兼容的分配放大器 | ||
|---|---|---|
| MTP DA4 和 MTP DA8 | 4 路和 8 路输出 MTP 双绞线分配放大器 | |
| 可选附件 | ||
|---|---|---|
| RSF 123 | 用于 3.5" 深产品的机架搁板套件 | |
| RSU 126 | 用于 6" 深产品的通用型机架搁板套件 | |
| MBU 123 | 用于 1/8、1/4 和 1/2 机架宽产品的薄型安装套件 | |
| PMK 100 | 用于 1/4 机架宽产品的杆式安装套件 | |
| PMK 300 | 用于 3 个 1/4 机架宽产品的多产品杆式安装套件 | |
| ZipClip 200 | 用于 1/8 和 1/4 机架宽产品的安装套件 | |
| PS 124 | 多路输出 12 V 直流电源 | |
| Skew-Free UTP | 用于 Extron VT、MTP 和 TP 系列模拟双绞线产品的增强型 Skew-Free™ 等长视音频 UTP 电缆 | |
Extron MTP 15HD RS 系列是多用途微型双绞线发送器和接收器系列，可通过单根非屏蔽双绞线电缆长距离传输 VGA 和 RS-232 串行控制信号至演示显示设备。它们兼容高达 1920 x 1200 (WUXGA) 的分辨率，支持的 VGA 信号电缆传输距离可达 185 m (600') 或更远，UXGA 信号可达 135 m (450') 或更远。
在那些需要将高分辨率视频信号长距离传输至管道空间有限的显示设备的系统中，或者布线会暴露及可见的系统中，MTP 15HD RS系列是理想之选。理想的应用场所包括机场的公共信息显示处、博物馆、电影院和旅馆。
特性
通过单根 CAT 5 类电缆在 185 m (600') 或更远的距离上接收高分辨率视频和 RS-232 信号
支持 RGBHV、RGBS、RGsB、RsGsBs、分量视频、S-视频和复合视频
兼容 HDTV 分量视频，双电平或三电平同步
独立的可变电平和峰值控制
MTP 缓冲输出，用于对多达 8 个接收器进行菊花链式连接
可对每种颜色进行独立的扭曲延时补偿调整 - 仅限 MTP RL 15HD RS SEQ
随附外置 Extron Everlast™ 电源，产品编号 #70-1174-01 — 该全球通用型电源具有经验证的高可靠性和低功耗
Extron Everlast 电源提供 7 年部件和人工保修
示意图
面板图
| MTP 15HD RS Series | |||
| Video | |||
|---|---|---|---|
| Gain | Unity | ||
| Number/signal type | |||
| MTP 4T 15HD RS | 4 sets of proprietary analog signals | ||
| All other models | 1 set of proprietary analog signals | ||
| Connectors | |||
| MTP 4T 15HD RS | 4 female RJ-45 | ||
| MTP R 15HD RSA D | 1 female RJ-45 on a pigtail | ||
| All other models | 1 female RJ-45 | ||
| Video input and loop-through — transmitter (MTP T 15HD RS, MTP C7 T 15HD RS, MTP 4T 15HD RS) | |||
| Number/signal type | 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (with bi-level or tri-level sync), S-video, or composite video 1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits) |
||
| Connectors | 2 female 15-pin HD | ||
| Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video |
||
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p | ||
| Impedance | 75 ohms | ||
| Horizontal frequency | 15 kHz to 130 kHz | ||
| Vertical frequency | 30 Hz to 150 Hz | ||
| Return loss | <-30 dB @ 5 MHz | ||
| DC offset (max. allowable) | 250 mV | ||
| Video output — receivers | |||
| Number/signal type | |||
| MTP R 15HD RSA D | 1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video | ||
| All other receivers | 1 set of proprietary analog signals 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi-/tri-level sync), S-video, or composite video |
||
| Connectors | |||
| MTP R 15HD RSA D | 1 female 15-pin HD | ||
| All other receivers | 1 female RJ-45 1 female 15-pin HD |
||
| Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video |
||
| Minimum/maximum levels | 0.3 V to 1.45 Vp-p | ||
| Impedance | 75 ohms | ||
| Return loss | <-30 dB @ 5 MHz | ||
| DC offset | <±20 mV with input at 0 offset | ||
| Skew compensation | 62 ns | ||
| Maximum resolution | |||
| MTP 1500RL 15HD models | Up to 1600x1200 and 1080p at 1500' Up to 1920x1200 and 2048x1080 at 1200' |
||
| All other models | Up to 1920x1200 or 2048x1080 or 1080p at 300' Up to 1024x768 at 600' |
||
|
|||
| Sync | |||
| Input type (transmitter) | RGBHV, RGBS, RGsB, RsGsBs | ||
| Output type (receivers) | RGBHV, RGBS, RGsB, RsGsBs | ||
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM | ||
| Input level (transmitter) | 3.5 V to 5.5 Vp-p, unterminated | ||
| Output level (receivers) | |||
| MTP 1500RL 15HD models | 0.3 Vp-p for component video (bi-level sync) 0.6 Vp-p for component video (tri-level sync) TTL: 4.0 V to 5.0 V p-p, unterminated for RGBHV, RGBS |
||
| All other models | 4.0 V to 5.0 Vp-p, unterminated | ||
| Input impedance | |||
| MTP C7 models | 573 ohms | ||
| All other models | 510 ohms | ||
| Output impedance | |||
| MTP C7 models | 92 ohms ±8% (25 mA) | ||
| All other models | 110 ohms | ||
| Polarity | |||
| Transmitter | Positive or negative (follows input polarity) | ||
| Receivers | Positive or negative (switch selectable) | ||
| Control/remote — external device (pass-through, unidirectional or bidirectional) | |||
| Serial control port input/output | |||
| MTP T 15HD RS, MTP C7 T 15HD RS, MTP 4T 15HD RS | RS-232 via (1) 3.5 mm, 3 pole captive screw connector | ||
| MTP R 15HD RSA D, MTP C7 RL 15HD RS, MTP C7 RL 15HD RS SEQ | 1 set of proprietary signals on a female RJ-45 jack | ||
| Serial control port output/input | |||
| MTP T 15HD RS, MTP C7 T 15HD RS, MTP 4T 15HD RS | 1 set of proprietary signals on a female RJ-45 jack | ||
| MTP R 15HD RSA D | RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole | ||
| All other receivers | RS-232 via a 3.5 mm, 3 pole captive screw connector | ||
| Baud rates | |||
| MTP R 15HD RSA D, MTP 1500RL 15HD RS, MTP 1500RL 15HD RS SEQ | Up to 38400 bps at up to 1000' (304.8 m) | ||
| All other models | Up to 38400 bps at up to 600' (183 m) | ||
|
|||
| Protocol | Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none |
||
|
|||
| Serial control pin configuration | Captive screw connectors: 1 = TX, 2 = RX, 3 = GND | ||
| General | |||
| Recommended cable type | |||
| Models other than C7 models | CAT 5/5e/6 (shielded or unshielded) | ||
| Required cable type | |||
| MTP C7 15HD models | Extron DTP26 or CAT 7 | ||
| Power | MTP 4T 15HD RS only: 100 VAC to 240 VAC, 50-60 Hz, 20 watts, internal | ||
| External power supply | All models except MTP 4T 15HD RS: 100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated |
||
| Power input requirements | For models except MTP 4T 15HD RS. | ||
| MTP 1500RL 15HD models | 12 VDC, 1.0 A max. | ||
| All other models | 12 VDC, 0.5 A | ||
| Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
||
| Cooling | |||
| MTP 1500RL 15HD models | Convection, vents sides to top | ||
| All other models | Convection, no vents | ||
| Mounting | |||
| Rack mount | |||
| MTP R 15HD RSA D | No | ||
| MTP 4T 15HD RS | Yes, with included mounting kit | ||
| All other models | Yes, with optional 1U rack shelf | ||
| Furniture mount | |||
| MTP R 15HD RSA D | Yes, using a standard electrical wall box or Decora ® size mud ring | ||
| MTP 1500RL 15HD models | No | ||
| All other models except MTP 4T 15HD RS | Yes, with optional mini under-desk mounting kit | ||
| Wall mount | |||
| MTP 1500RL 15HD models | Yes, with optional wall mounting kit | ||
| Pole mount | |||
| MTP R 15HD RSA D | No | ||
| MTP 1500RL 15HD models | No | ||
| All other models except MTP 4T 15HD RS | Yes, with optional pole mounting kit | ||
| Enclosure type | Metal | ||
| Enclosure dimensions | |||
| MTP R 15HD RSA D | |||
| Faceplate | 2.6" H* x 1.3" W x 0.24" D (6.6 cm H* x 3.3 cm W x 0.5 cm D) *Overall height is 4.1" (10.4 cm) including mounting tabs. (Fits the opening in a 1 gang, 4.4" H x 2.7" W Decora ® -style wallplate. Depth excludes connectors.) |
||
| Device | 2.75" H x 1.65" W x 1.3" D (7.0 cm H x 4.2 cm W x3.3 cm D) (Depth excludes connectors.) |
||
| MTP 4T 15HD RS | 1.7" H x 17.5" W x 8.5" D (1U high, full rack wide) (4.3 cm H x 44.4 cm W x 21.6 cm D) (Depth excludes connectors.) |
||
| MTP 1500RL 15HD models | 1.0" H x 8.75" W x 6.0" D (half rack wide) (2.5 cm H x22.2 cm W x15.2 cm D) (Depth excludes connectors.) |
||
| All other models | 1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide) (4.3 cm H x 10.9 cm W x 7.6 cm D) (Depth excludes connectors.) |
||
| Product weight | |||
| MTP 4T 15HD RS | 6.0 lbs (2.7 kg) | ||
| MTP 1500RL 15HD models | 1 lb (0.5 kg) | ||
| All other models | 0.4 lbs (0.2 kg) | ||
| Shipping weight | |||
| MTP 4T 15HD RS | 10 lbs (5 kg) | ||
| All other models | 2 lbs (1 kg) | ||
| Vibration | ISTA 1A in carton (International Safe Transit Association) | ||
| Regulatory compliance | |||
| Safety | CE, c-UL, UL | ||
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI | ||
| Product warranty | 3 years parts and labor | ||
|
|||
|
|||
| (7.6-111909-D10) | |||
| 可选附件 | ||
|---|---|---|
| RSF 123 | 用于 3.5" 深产品的机架搁板套件 | |
| RSU 126 | 用于 6" 深产品的通用型机架搁板套件 | |
| MBU 123 | 用于 1/8、1/4 和 1/2 机架宽产品的薄型安装套件 | |
| PMK 100 | 用于 1/4 机架宽产品的杆式安装套件 | |
| PMK 300 | 用于 3 个 1/4 机架宽产品的多产品杆式安装套件 | |
| ZipClip 200 | 用于 1/8 和 1/4 机架宽产品的安装套件 | |
| PS 124 | 多路输出 12 V 直流电源 | |
| Skew-Free UTP | 用于 Extron VT、MTP 和 TP 系列模拟双绞线产品的增强型 Skew-Free™ 等长视音频 UTP 电缆 | |
中国上海市松江区茸华路 686 号
(联系就说在DAV音视工程网上看到的)
Sales-China@Extron.com
021-3760 1566
爱思创电子（上海）有限公司（爱思创Extron中国）全球总部位于美国加州，是世界领先的专业视音频系统集成产品的生产商。爱思创Extron产品主要包括视音频控制系统、计算机视频接口、切换器、矩阵切换器、分配放大器、音频放大器、扬声器、双绞线和光纤设备、视频图像解析度转换器、视音频信号处理器、视音频流媒体产品、教室声场系统及高分辨率电缆。爱思创Extron电子提供专业视音频工程、培训、设计、演示支持。
DAV首页