DMP 128 FlexPlus 系列紧凑型 Dante 数字矩阵处理器的半机架宽外壳具有 12 个 FlexInput 通道,可支持完整的 DSP 功能,包括 AEC (回声消除) 和 Dante 连接。DMP128FlexPlus 提供一个扩展的混音矩阵、一个 USB 音频接口并兼容模拟音频,能够轻松地连接及路由多种类型的源信号,以满足不同的模拟和数字系统需求。为适应协作式应用环境,V 型号可支持多达 8 个 VoIP 线路。DMP128FlexPlus 的其它特性包括:用于连接音频控制面板的 ACP 总线、与 DTPCrossPoint 或另一台 DMP 进行双向数字连接的扩展端口、8 个音频文件播放器以及可配置的宏指令等,可适用于从协作式空间到大型会议室等各种应用环境。
快速参考 |
---|
DMP 128 FlexPlus (宣传册) |
DMP 128 FlexPlus Setup Guide (用户手册) |
DMP 128 FlexPlus User Guide (用户手册) |
Dante 网络产品 | ||
---|---|---|
AXI 44 AT | 4 路输入、4 路输出 Dante 音频接口 | |
AXI 22 AT | 2 路输入、2 路输出 Dante 音频接口 | |
AXI 22 AT D | 2 路输入、2 路输出 Dante 音频接口 - Decorator 型墙面板 | |
AXI 02 AT | 2 路输出 Dante 音频接口 | |
AXP 64 C AT | 支持 AEC 和 Dante 的 6 路输入、4 路输出音频扩展处理器 | |
AXP 50 C AT | 支持 AEC 和 Dante 的 5 路输入音频扩展处理器 | |
NetPA 502 AT | 支持 Dante 的两通道音频功率放大器 – 每个通道 50 W | |
NetPA 1001-70V AT | 支持 Dante 的 70 V 单声道音频功率放大器 – 100 W |
可选附件 | ||
---|---|---|
ACP 100 | 带音量和 6 个控制按键的音频控制面板 美式 2 单元 |
|
ACP 105 D | 带 5 个按键的音频控制面板 Decorator 型 |
|
ACP 105 EU | Audio Control Panel with 5 Buttons Flex55 and EU |
|
ACP 105 MK | Audio Control Panel with 5 Buttons – MK | |
ACP 106 D | 带 6 个按键的音频控制面板 Decorator 型 |
|
ACP 106 EU | 带 6 个按键的音频控制面板 Flex55 和欧式 |
|
ACP 106 MK | 带 6 个按键的音频控制面板 – MK | |
ACP VC1 D | Audio Control Panel with Volume and Mute Decorator-Style |
|
ACP VC1 EU | Audio Control Panel with Volume and Mute Flex55 and EU |
|
ACP VC1 MK | Audio Control Panel with Volume and Mute - MK | |
CSC 6 | 螺丝锁定器至 CATx 电缆适配器 | |
RSU 129 | 用于 9.5" 深产品的通用型机架搁板套件 | |
RSB 129 | Basic Rack Shelf for 9.5" Deep Products | |
UTS 100 系列 | 桌下搁板系统 | |
半机架搁板系统 | 半机架宽机架搁板和附件 |
示意图
面板图
DMP 128 FlexPlus | |||
Audio system | |||
---|---|---|---|
Gain | Balanced output: 0 dB, unbalanced output: -6 dB | ||
Frequency response | 20 Hz to 20 kHz, ±0.2 dB | ||
THD + Noise | <0.01%, 20 Hz to 20 kHz, at maximum level | ||
S/N | |||
Analog In to Analog Out | >107 dB, 20 Hz to 20 kHz, at maximum balanced output (unweighted) | ||
Analog In to Digital Out | 110 dB, 20 Hz to 20 kHz, at full-scale output (unweighted) | ||
Digital In to Analog Out | 115 dB, 20 Hz to 20 kHz, at maximum balanced output (unweighted) | ||
Crosstalk | <-90 dB @ 20 Hz to 20 kHz, fully loaded | ||
Volume control | -100 dB to 0 dB (control 0 to 100 in 0.1 dB steps) | ||
Audio input | |||
Number/signal type | 4 mono (or 2 stereo), mic/line, balanced/unbalanced, 4 with phantom power | ||
Connectors | (2) 3.5 mm captive screw, 6 pole, mono, balanced/unbalanced | ||
Impedance | >10k ohms balanced/unbalanced | ||
Nominal level | -60 dBV,+4 dBu, -10 dBVadjustablevia input gain | ||
Maximum level | +21 dBuat rated THD+N whenmic gain is set to 0 dB | ||
Equivalent input noise | <-120 dBV (1 µVrms) at 40 dB input gain | ||
CMRR | >60 dB typical | ||
Input gain adjustment | -18 dB to +80 dB in 0.1 dB steps, adjustable per input | ||
DC phantom power | +48 VDC, + 10%(inputs 1-4) can be switched on or off per input | ||
|
|||
Audio output | |||
Number/signal type | 8 mono (or 4 stereo), line, balanced/unbalanced | ||
Connectors | (4) 3.5 mm captive screw, 6 pole, mono, balanced/unbalanced | ||
Impedance | 100 ohms balanced, 50 ohms unbalanced | ||
Gain error | ±0.1 dB channel to channel | ||
Maximum level (Hi-Z) | >+21 dBu balanced, >+15 dBu unbalanced | ||
Audio processing | |||
A/D, D/A conversion | 24-bit,48 kHz | ||
AEC tail length | >200 msec | ||
AEC convergence | Up to 60 dB/sec | ||
Noise cancellation | Up to 20 dB, software selectable | ||
EXP port | |||
Transmission type | Proprietary | ||
Connector | 1 RJ-45 | ||
Inputs | 16 channels Rx | ||
Outputs | 16 channels Tx | ||
Audio format | Uncompressed, 24-bit, 48 kHz | ||
EXP cable | Shielded CAT6 up to 10 meters (1 foot cable included) | ||
USB audio port | |||
Connector | 1 rear panel USB mini-B | ||
USB standards | USB 2.0, high speed | ||
AT ports — audio transport | |||
Transmission | Dante/AES-67, software selectable | ||
Connectors | 2 RJ-45, 2-port 1 Gbps switch to Dante interface | ||
Inputs | 48 channels Rx | ||
Outputs | 24 channels Tx | ||
Audio format | Uncompressed, 24-bit, 48 kHz | ||
Latency | Deterministic, based on user selections: 0.25 ms, 0.5 ms, 1.0 ms (default), 2.0 ms, 5.0 ms | ||
VoIP port (DMP 128 FlexPlus V model only) | |||
Connector | 1 RJ-45 | ||
Data rate | 10/100/1000 Base-T | ||
Signaling protocol | Session Initiation Protocol (SIP), RFC 3261 and related RFCs | ||
Discovery protocol | LLDP-MED (optional) | ||
Lines | Up to 8 concurrent, independent extensions | ||
Codec support | Various ITU, including wideband | ||
Default settings | Link speed and duplex level = autodetected IP address = 192.168.1.254 Subnet mask = 255.255.255.0 Default gateway = 0.0.0.0 DHCP = off |
||
Control/remote | |||
Serial host control port | 1 bidirectional RS-232, 3.5 mm captive screw, 3 pole | ||
Baud rate and protocol | 38400 baud, 8 data bits, 1 stop bit, no parity | ||
Pin configuration | 1 = Tx, 2 = Rx, 3 = G | ||
USB control port | 1 front panel USB mini-B | ||
USB standards | USB 2.0, high speed | ||
ACP control port | (1) 3.5 mm captive screw, 4 pole, supports up to 8 panels | ||
Pin configuration | 1 = +12V, 2 = +S, 3 = -S, 4 = G | ||
Power supply | 6 Watts max | ||
Digital I/O | (2) 3.5 mm captive screw, 3 pole | ||
Pin configuration | 1 = In, 2 = G, 3 = Out 1 | ||
Voltage range | Input = 0V to +12V Output = 0V (low), 5V (high) Software programmable |
||
Ethernet host port | 1 RJ-45 | ||
Data rate | 10/100/1000 Base-T | ||
Protocol | ARP, ICMP, IP, TCP, DHCP, HTTPS, Telnet, SSH | ||
Default settings | Link speed and duplex level = autodetected IP address = 192.168.254.254 Subnet mask = 255.255.255.0 Default gateway = 0.0.0.0 DHCP = off |
||
Web server | Up to 200 simultaneous sessions | ||
Program control | Extron DSP Configurator control/configuration program for Windows ® Extron Simple Instruction Set (SIS ™ ) Microsoft ® Internet Explorer ® , Telnet |
||
General | |||
Power supply | External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 2 A, 24 watts |
||
Power consumption | |||
DMP 128 FlexPlus C AT | |||
Device | 14.9 watts | ||
Device and power supply | 17.1 watts | ||
DMP 128 FlexPlus C V AT | |||
Device | 15.6 watts | ||
Device and power supply | 17.9 watts | ||
Thermal dissipation | |||
DMP 128 FlexPlus C AT | |||
Device | 40.6 BTU/hr | ||
Device and power supply | 48.0 BTU/hr | ||
DMP 128 FlexPlus C V AT | |||
Device | 43.1 BTU/hr | ||
Device and power supply | 50.8 BTU/hr | ||
Temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
||
Cooling | Fan, front to back, variable speed, OFF when ambient temperature is less than 45 °C | ||
Mounting | |||
Rack mount | Yes, with optional 1U rack shelf | ||
Furniture mount | Yes, with optional under-desk mounting kit | ||
Enclosure type | Metal | ||
Enclosure dimensions | 1.7" H x 8.7" W x 9.5" D (1U high, half rack wide) (4.3 cm H x 22.1 cm W x 24.1 cm D) |
||
Product weight | 2.4 lbs (1.1 kg) | ||
Regulatory compliance | CE, c-UL, UL, CE, C-Tick, FCC Class A, ICES, RoHS, VCCI, WEEE | ||
Warranty | 3 years parts and labor | ||
|
|||
|
|||
(4673-080119) |
可选附件 | ||
---|---|---|
ACP 100 | 带音量和 6 个控制按键的音频控制面板 美式 2 单元 |
|
ACP 105 D | 带 5 个按键的音频控制面板 Decorator 型 |
|
ACP 105 EU | Audio Control Panel with 5 Buttons Flex55 and EU |
|
ACP 105 MK | Audio Control Panel with 5 Buttons – MK | |
ACP 106 D | 带 6 个按键的音频控制面板 Decorator 型 |
|
ACP 106 EU | 带 6 个按键的音频控制面板 Flex55 和欧式 |
|
ACP 106 MK | 带 6 个按键的音频控制面板 – MK | |
ACP VC1 D | Audio Control Panel with Volume and Mute Decorator-Style |
|
ACP VC1 EU | Audio Control Panel with Volume and Mute Flex55 and EU |
|
ACP VC1 MK | Audio Control Panel with Volume and Mute - MK | |
CSC 6 | 螺丝锁定器至 CATx 电缆适配器 | |
RSU 129 | 用于 9.5" 深产品的通用型机架搁板套件 | |
RSB 129 | Basic Rack Shelf for 9.5" Deep Products | |
UTS 100 系列 | 桌下搁板系统 | |
半机架搁板系统 | 半机架宽机架搁板和附件 |
中国上海市松江区茸华路 686 号
(联系就说在DAV音视工程网上看到的)
Sales-China@Extron.com
021-3760 1566
爱思创电子(上海)有限公司(爱思创Extron中国)全球总部位于美国加州,是世界领先的专业视音频系统集成产品的生产商。爱思创Extron产品主要包括视音频控制系统、计算机视频接口、切换器、矩阵切换器、分配放大器、音频放大器、扬声器、双绞线和光纤设备、视频图像解析度转换器、视音频信号处理器、视音频流媒体产品、教室声场系统及高分辨率电缆。爱思创Extron电子提供专业视音频工程、培训、设计、演示支持。